New Holland Heavy Duty Skid Steer Hydraulic Breaker🔵 Mid
🟡 High Flow
⚠ High-flow machine required
✓ Compatible with high-flow CTL
⚠ Too heavy for most small-frame machines
✓ Best on mid-frame or large-frame machines
View on agriculture.newholland.com →
Overview
The New Holland Heavy Duty Skid Steer Hydraulic Breaker demolishes concrete slabs, asphalt, rock faces, and frozen ground that buckets cannot penetrate. New Holland agriculture and construction dealers are spread across all Canadian provinces, providing local support for attachments. Impact energy and blow rate determine performance on hard material; match the breaker class to your machine's auxiliary hydraulic output. Used extensively on Canadian construction and utility sites. Available through New Holland dealers across Canada.
Canada Availability
Available through New Holland dealers across Canada.
Key Facts
- Brand: New Holland Construction
- Type: heavy-duty hydraulic breaker
- Drive: high-flow auxiliary hydraulic
- Mount: New Holland quick attach (SSQA compatible)
- Weight: 1200–2000 lbs
- Hydraulic flow: 15–20 GPM
Is This Right For You?
✅ Buy if…
- You break large reinforced concrete foundations, thick rock, or concrete retaining walls regularly
- Your skid steer is a large-frame machine (80+ HP) rated for a heavy hammer attachment
- Production rate matters — heavy-duty breakers complete demolition jobs significantly faster than medium class
⛔ Skip if…
- Your machine is medium-frame or smaller — a heavy breaker can exceed carrier weight class limits and damage hydraulics
- Occasional light demolition is your only use — a medium-duty breaker handles that range at lower cost
🔍 Also consider…
- Medium-duty hydraulic breaker for smaller machines and occasional demolition
- Light-duty breaker for compact machines doing concrete curb or small slab work
🔧 Machine Compatibility
Designed for New Holland machines but mounts to any skid steer or CTL with a universal SSQA quick-attach plate.
About New Holland in Canada
New Holland attachments are available through CNH dealer locations across Canada. New Holland has a strong presence in agricultural regions and their attachments are built to match the hydraulic specs of their skid steers and compact track loaders.
Care & Maintenance
- Check nitrogen buffer gas pressure at the start of every season and whenever impact energy feels reduced — low gas pressure is the most common cause of reduced performance
- Lubricate the tool (chisel) bushing and retainer pins before every use — dry bushings accelerate side-loading wear on both the bushing and the tool shank
- Inspect the lower bushing for wear after every 40 hours — a worn bushing allows chisel wobble, reducing impact energy delivery and accelerating shank wear
- Never blank-fire the breaker — operating without material contact destroys the internal valve in minutes; this is the most common cause of breaker failures
- Verify return-line back-pressure annually — back-pressure exceeding the breaker's rated limit destroys the valve seal progressively and may not be immediately obvious
How to Connect
- Attach breaker using Bob-Tach
- Connect single aux hydraulic circuit (breakers use one-way flow)
- Set machine to single-action aux mode if available
- Run 5 seconds at idle before working to allow oil to circulate
⚠ Safety NoteBreakers use single-direction flow. Do not run breaker in same position for more than 30 seconds — move to avoid blank-firing damage.
⚒️ Before You Buy a Hydraulic Breaker
Breaker sizing and hydraulic matching are critical — an oversized or underpowered breaker wears out faster and can damage your machine.
- Size the breaker class to your machine's rated operating capacity (ROC) Breaker sizing guide →
- Verify your machine's GPM and PSI output match the breaker's requirement Hydraulic flow guide →
- Confirm anti-blank-fire protection — protects both the breaker and your machine
Find a Breaker Dealer →
Complete the job — you might also need:
✅ Last checked: March 2026
Source: skidsteerattachments.ca/catalog/hydraulic-breakers/new-holland-hydraulic-breaker-heavy/
Ready to Buy? Check These First
⚙️
Confirm Machine Fit
Verify your machine's hydraulic flow meets this attachment's requirements before ordering. High-flow attachments need 25–45+ GPM — standard flow machines won't run them properly.
Check your machine's flow →
🇨🇦
Find a Canadian Dealer
Buy through a Canadian dealer for warranty support, parts, and service. Avoid grey-market imports on high-ticket attachments.
Find dealers by province →
