HLA SP350008 96-Inch 3500 Series Snow Pusher🔵 Mid
✓ No hydraulics required
View on hlasnow.com →
Overview
The HLA SP350008 is a 96-inch (8-foot) snow pusher in HLA's 3500 Series, sized for skid steers and compact wheel loaders from 5,500 to 15,000 lbs operating weight. The 8-foot pusher is the most common size for Canadian commercial lot clearing and farm yard use — wide enough for serious volume clearing while fitting through most farm gates. HLA builds this in Ontario with double sidewalls, a spring trip cutting edge, and AR400 skid bars.
Canada Availability
Available in Canada through HLA Attachments and HLA Snow dealers. Ontario-manufactured — available at dealers across Canada including GLC Equipment.
Key Facts
- Pusher width: 96 inches (8 feet)
- Mouldboard height: 38 inches
- Depth: 36 inches
- Weight: approximately 1,055 lbs
- Maximum operating weight of carrier: 15,000 lbs
- Cutting edge: steel, replaceable and reversible
- Spring trip cutting edge — protects against hidden obstacles and frost heaves
- AR400 high tensile adjustable steel skid bars
- Double sidewall construction
- 2-year commercial warranty
- Hydraulic flow: none required — passive attachment, no auxiliary hydraulics
✅ Specs sourced from hlasnow.com · Last verified: March 2026
Is This Right For You?
✅ Buy if…
- You push snow on flat commercial lots, parking decks, or loading docks with a defined push perimeter
- You don't have room or budget for a blower — pushers cost far less and maintain well
⛔ Skip if…
- Your site has no windrow drop zone — pushers pile snow that has to go somewhere
- Wet, heavy Ontario snow is your primary challenge — heavy packs reduce machine traction with a full pusher
🔍 Also consider…
- Sectional pusher if your site has frost heaves or uneven pavement you need the wings to follow
- Snow blower attachment if bank height from repeated pushes is becoming a problem
🔧 Machine Compatibility
Wide attachment — verify your machine's rated operating capacity (ROC) before ordering. Compatible with all skid steer brands via universal SSQA quick attach — no auxiliary hydraulics required.
About HLA in Canada
HLA Attachments is an Ontario-based manufacturer that designs and builds attachments in Waterloo, ON, with a dealer network spanning all provinces. Backed by a Canadian warranty and local parts availability, HLA is one of the most trusted names on Canadian job sites.
Care & Maintenance
- Inspect the trip-edge blade for wear before each season and replace when worn below the wear indicator line — a worn-through trip-edge transfers full impact to the blade frame
- Grease all trip-edge pivot and hinge points after every major pushing session, especially after work in extreme cold where grease migrates out of joints faster
- Check side board welds for cracking after frost heave strikes — box sides bear significant impact forces during high-speed frost heave hits
- Rinse salt off after every use and before extended storage — road salt accelerates rust on unpainted steel edges and frame members faster than people expect
- Store off the ground on blocks or a pallet to prevent the cutting edge from sitting in standing water and rusting from below
How to Connect
- Back machine into push frame receiver
- Lower boom to slide trip edges into receiver arms
- Engage mounting pins or latch
- Raise slightly off ground and test trip edge reset manually if accessible
⚠ Safety NoteSnow pushers are passive (no hydraulics) on most models — mounting is mechanical only
❄️ Before You Buy a Snow Pusher
Snow pusher sizing is machine-dependent — an oversized box overloads your loader arms; undersizing means extra passes on large lots.
- Match pusher width to your machine's ROC and tipping load Attachment sizing guide →
- Trip-edge vs sectional edge — trip edge for paved lots, sectional for uneven surfaces Snow pusher guide →
- Buy before November — Canadian dealers sell out of popular sizes by mid-winter
Find a Snow Pusher Dealer →
Complete the job — you might also need:
✅ Last checked: March 2026
Source: skidsteerattachments.ca/catalog/snow-pushers/hla-sp350008-snow-pusher/
