HLA SP350012 144-Inch 3500 Series Snow Pusher🔵 Mid
✓ No hydraulics required
View on hlasnow.com →
Overview
The HLA SP350012 is a 144-inch (12-foot) snow pusher in HLA's 3500 Series, designed for large-frame skid steers and compact wheel loaders pushing to their rated operating weight. At 12 feet wide, this pusher is sized for high-volume commercial clearing — large box stores, municipal lots, and industrial yards where maximum push width per pass is critical to job productivity. Made in Ontario by HLA Attachments. Spring trip edge and AR400 skid bars are standard.
Canada Availability
Available in Canada through HLA Attachments and HLA Snow dealers. Ontario-manufactured.
Key Facts
- Pusher width: 144 inches (12 feet)
- Mouldboard height: 38 inches
- Depth: 36 inches
- Weight: approximately 1,370 lbs
- Maximum operating weight of carrier: 15,000 lbs
- Cutting edge: steel, replaceable and reversible
- Spring trip cutting edge
- AR400 adjustable steel skid bars
- Double sidewall construction
- 2-year commercial warranty
- Hydraulic flow: none required — passive attachment, no auxiliary hydraulics
✅ Specs sourced from hlasnow.com · Last verified: March 2026
Is This Right For You?
✅ Buy if…
- You push snow on flat commercial lots, parking decks, or loading docks with a defined push perimeter
- You don't have room or budget for a blower — pushers cost far less and maintain well
⛔ Skip if…
- Your site has no windrow drop zone — pushers pile snow that has to go somewhere
- Wet, heavy Ontario snow is your primary challenge — heavy packs reduce machine traction with a full pusher
🔍 Also consider…
- Sectional pusher if your site has frost heaves or uneven pavement you need the wings to follow
- Snow blower attachment if bank height from repeated pushes is becoming a problem
🔧 Machine Compatibility
Wide attachment — verify your machine's rated operating capacity (ROC) before ordering. Compatible with all skid steer brands via universal SSQA quick attach — no auxiliary hydraulics required.
About HLA in Canada
HLA Attachments is an Ontario-based manufacturer that designs and builds attachments in Waterloo, ON, with a dealer network spanning all provinces. Backed by a Canadian warranty and local parts availability, HLA is one of the most trusted names on Canadian job sites.
Care & Maintenance
- Inspect the trip-edge blade for wear before each season and replace when worn below the wear indicator line — a worn-through trip-edge transfers full impact to the blade frame
- Grease all trip-edge pivot and hinge points after every major pushing session, especially after work in extreme cold where grease migrates out of joints faster
- Check side board welds for cracking after frost heave strikes — box sides bear significant impact forces during high-speed frost heave hits
- Rinse salt off after every use and before extended storage — road salt accelerates rust on unpainted steel edges and frame members faster than people expect
- Store off the ground on blocks or a pallet to prevent the cutting edge from sitting in standing water and rusting from below
How to Connect
- Back machine into push frame receiver
- Lower boom to slide trip edges into receiver arms
- Engage mounting pins or latch
- Raise slightly off ground and test trip edge reset manually if accessible
⚠ Safety NoteSnow pushers are passive (no hydraulics) on most models — mounting is mechanical only
❄️ Before You Buy a Snow Pusher
Snow pusher sizing is machine-dependent — an oversized box overloads your loader arms; undersizing means extra passes on large lots.
- Match pusher width to your machine's ROC and tipping load Attachment sizing guide →
- Trip-edge vs sectional edge — trip edge for paved lots, sectional for uneven surfaces Snow pusher guide →
- Buy before November — Canadian dealers sell out of popular sizes by mid-winter
Find a Snow Pusher Dealer →
Complete the job — you might also need:
✅ Last checked: March 2026
Source: skidsteerattachments.ca/catalog/snow-pushers/hla-sp350012-snow-pusher/
