John Deere Worksite Pro SP84 Snow Pusher🔵 Mid
✓ No hydraulics required
✓ Fits most skid steers, including small-frame
View on deere.com →
Overview
An 84-inch snow pusher in John Deere's Worksite Pro line. The SP84 is sized for mid-frame skid steers and fits through standard parking lot drive lanes while still moving a useful volume of snow. Rubber cutting edge protects finished pavement and handles the frost heave irregularities common on Canadian commercial lots — a steel edge in those conditions catches and lifts the bucket rather than skimming. Available through Brandt dealers across Canada.
Canada Availability
Available in Canada through Brandt / John Deere Worksite Pro. Common on mid-frame skid steers used in Canadian commercial snow contracts.
Key Facts
- Working width: 84 inches (213 cm)
- Cutting edge: rubber — protects pavement, handles frost heaves
- Application: commercial parking lots, sidewalks, site clearing, farm yards
- Box design retains snow load for efficient transport to windrow
- No hydraulics required
- SSQA (universal skid steer quick attach) mount
- Compatible with John Deere skid steers and compact track loaders
- Typical weight: 450–580 lbs
- Hydraulic flow: none required — passive attachment, no auxiliary hydraulics
✅ Specs sourced from deere.com · Last verified: March 2026
Is This Right For You?
✅ Buy if…
- You push snow on flat commercial lots, parking decks, or loading docks with a defined push perimeter
- You don't have room or budget for a blower — pushers cost far less and maintain well
⛔ Skip if…
- Your site has no windrow drop zone — pushers pile snow that has to go somewhere
- Wet, heavy Ontario snow is your primary challenge — heavy packs reduce machine traction with a full pusher
🔍 Also consider…
- Sectional pusher if your site has frost heaves or uneven pavement you need the wings to follow
- Snow blower attachment if bank height from repeated pushes is becoming a problem
🔧 Machine Compatibility
Designed for John Deere machines but mounts to any skid steer or CTL with a universal SSQA quick-attach plate.
About John Deere in Canada
John Deere attachments are available through an extensive Canadian dealer network, ensuring local service, parts availability, and warranty support coast to coast. Designed to pair with JD machines but compatible with any skid steer via universal quick attach.
Care & Maintenance
- Inspect the trip-edge blade for wear before each season and replace when worn below the wear indicator line — a worn-through trip-edge transfers full impact to the blade frame
- Grease all trip-edge pivot and hinge points after every major pushing session, especially after work in extreme cold where grease migrates out of joints faster
- Check side board welds for cracking after frost heave strikes — box sides bear significant impact forces during high-speed frost heave hits
- Rinse salt off after every use and before extended storage — road salt accelerates rust on unpainted steel edges and frame members faster than people expect
- Store off the ground on blocks or a pallet to prevent the cutting edge from sitting in standing water and rusting from below
How to Connect
- Back machine into push frame receiver
- Lower boom to slide trip edges into receiver arms
- Engage mounting pins or latch
- Raise slightly off ground and test trip edge reset manually if accessible
⚠ Safety NoteSnow pushers are passive (no hydraulics) on most models — mounting is mechanical only
❄️ Before You Buy a Snow Pusher
Snow pusher sizing is machine-dependent — an oversized box overloads your loader arms; undersizing means extra passes on large lots.
- Match pusher width to your machine's ROC and tipping load Attachment sizing guide →
- Trip-edge vs sectional edge — trip edge for paved lots, sectional for uneven surfaces Snow pusher guide →
- Buy before November — Canadian dealers sell out of popular sizes by mid-winter
Find a Snow Pusher Dealer →
Complete the job — you might also need:
✅ Last checked: March 2026
Source: skidsteerattachments.ca/catalog/snow-pushers/john-deere-sp84-snow-pusher/
