John Deere Worksite Pro SP8 Snow Pusher🔵 Mid
✓ No hydraulics required
✓ Fits most skid steers, including small-frame
View on brandt.ca →
Overview
The SP8 is an 8-foot (96-inch) box-style snow pusher in John Deere's Worksite Pro lineup. Wider than the SP84 by a full foot, it moves more snow per pass on mid-to-large commercial lots while still fitting standard parking drive lanes. The box design contains the snow load — no side spillage — making it efficient for pushing large volumes to lot edges in fewer trips. Rubber cutting edge protects pavement and handles the uneven surfaces and frost heaves common on Canadian commercial properties. No hydraulics required.
Canada Availability
Available in Canada through Brandt / John Deere Worksite Pro — dealer locations in BC, AB, SK, MB, and ON.
Key Facts
- Working width: 8 feet (96 inches)
- Cutting edge: rubber — protects pavement, handles frost heaves
- Application: commercial parking lots, industrial yards, site clearing
- Box design retains snow load — no side-casting
- No hydraulics required
- SSQA (universal skid steer quick attach) mount
- Compatible with mid-to-large frame skid steers and compact track loaders
- Typical weight: 450–580 lbs
- Hydraulic flow: none required — passive attachment, no auxiliary hydraulics
✅ Specs sourced from brandt.ca · Last verified: March 2026
Is This Right For You?
✅ Buy if…
- You push snow on flat commercial lots, parking decks, or loading docks with a defined push perimeter
- You don't have room or budget for a blower — pushers cost far less and maintain well
⛔ Skip if…
- Your site has no windrow drop zone — pushers pile snow that has to go somewhere
- Wet, heavy Ontario snow is your primary challenge — heavy packs reduce machine traction with a full pusher
🔍 Also consider…
- Sectional pusher if your site has frost heaves or uneven pavement you need the wings to follow
- Snow blower attachment if bank height from repeated pushes is becoming a problem
🔧 Machine Compatibility
Compatible with compact track loaders and large-frame skid steers (S750+ class). Verify your machine's rated operating capacity (ROC) before ordering.
About John Deere in Canada
John Deere attachments are available through an extensive Canadian dealer network, ensuring local service, parts availability, and warranty support coast to coast. Designed to pair with JD machines but compatible with any skid steer via universal quick attach.
Care & Maintenance
- Inspect the trip-edge blade for wear before each season and replace when worn below the wear indicator line — a worn-through trip-edge transfers full impact to the blade frame
- Grease all trip-edge pivot and hinge points after every major pushing session, especially after work in extreme cold where grease migrates out of joints faster
- Check side board welds for cracking after frost heave strikes — box sides bear significant impact forces during high-speed frost heave hits
- Rinse salt off after every use and before extended storage — road salt accelerates rust on unpainted steel edges and frame members faster than people expect
- Store off the ground on blocks or a pallet to prevent the cutting edge from sitting in standing water and rusting from below
How to Connect
- Back machine into push frame receiver
- Lower boom to slide trip edges into receiver arms
- Engage mounting pins or latch
- Raise slightly off ground and test trip edge reset manually if accessible
⚠ Safety NoteSnow pushers are passive (no hydraulics) on most models — mounting is mechanical only
❄️ Before You Buy a Snow Pusher
Snow pusher sizing is machine-dependent — an oversized box overloads your loader arms; undersizing means extra passes on large lots.
- Match pusher width to your machine's ROC and tipping load Attachment sizing guide →
- Trip-edge vs sectional edge — trip edge for paved lots, sectional for uneven surfaces Snow pusher guide →
- Buy before November — Canadian dealers sell out of popular sizes by mid-winter
Find a Snow Pusher Dealer →
Complete the job — you might also need:
✅ Last checked: March 2026
Source: skidsteerattachments.ca/catalog/snow-pushers/john-deere-worksite-pro-sp8-snow-pusher/
