TMG Industrial TMG-SP07 7' Snow Pusher💚 Budget
✓ No hydraulics required
✓ Fits most skid steers, including small-frame
View on tmgindustrial.com →
Overview
The TMG-SP07 is a 7-foot (82-inch) skid steer snow pusher for commercial lot clearing and large residential driveways. The bolt-on high-tensile steel cutting edge scrapes to the pavement surface cleanly, reducing the amount of ice melt needed after each push. Pivoting wear shoes at the bottom corners protect the cutting edge on uneven pavement and extend service life. Integrated side braces stiffen the box structure under heavy wet-snow loads. At 550 lbs this is a manageable weight for 40–70 HP machines. Suited for Canadian winters across all regions—straightforward construction means easy on-farm repairs if needed. SSQA universal mount.
Canada Availability
TMG Industrial ships from Richmond, BC. National shipping available across Canada.
Key Facts
- Working width: 82 inches (7 feet)
- Weight: 550 lbs
- Cutting edge: Bolt-on high-tensile steel
- Wear shoes: Pivoting, extends cutting edge life
- Side braces: Integrated structural reinforcement
- Mount: Universal SSQA
- Carrier requirement: 40–70 HP skid steers
- Application: Commercial parking lots, large driveways, farm yards, loading areas
- Hydraulic flow: none required — passive attachment, no auxiliary hydraulics
Is This Right For You?
✅ Buy if…
- You push snow on flat commercial lots, parking decks, or loading docks with a defined push perimeter
- You don't have room or budget for a blower — pushers cost far less and maintain well
⛔ Skip if…
- Your site has no windrow drop zone — pushers pile snow that has to go somewhere
- Wet, heavy Ontario snow is your primary challenge — heavy packs reduce machine traction with a full pusher
🔍 Also consider…
- Sectional pusher if your site has frost heaves or uneven pavement you need the wings to follow
- Snow blower attachment if bank height from repeated pushes is becoming a problem
🔧 Machine Compatibility
Compatible with all skid steer brands via universal SSQA quick attach. No auxiliary hydraulics required — operates off the loader arms.
About TMG Industrial in Canada
TMG Industrial imports and distributes a broad range of construction attachments from its Canadian warehouses, offering competitive pricing with delivery across Canada. A popular choice for contractors who want solid value without long lead times.
Care & Maintenance
- Inspect the trip-edge blade for wear before each season and replace when worn below the wear indicator line — a worn-through trip-edge transfers full impact to the blade frame
- Grease all trip-edge pivot and hinge points after every major pushing session, especially after work in extreme cold where grease migrates out of joints faster
- Check side board welds for cracking after frost heave strikes — box sides bear significant impact forces during high-speed frost heave hits
- Rinse salt off after every use and before extended storage — road salt accelerates rust on unpainted steel edges and frame members faster than people expect
- Store off the ground on blocks or a pallet to prevent the cutting edge from sitting in standing water and rusting from below
How to Connect
- Back machine into push frame receiver
- Lower boom to slide trip edges into receiver arms
- Engage mounting pins or latch
- Raise slightly off ground and test trip edge reset manually if accessible
⚠ Safety NoteSnow pushers are passive (no hydraulics) on most models — mounting is mechanical only
❄️ Before You Buy a Snow Pusher
Snow pusher sizing is machine-dependent — an oversized box overloads your loader arms; undersizing means extra passes on large lots.
- Match pusher width to your machine's ROC and tipping load Attachment sizing guide →
- Trip-edge vs sectional edge — trip edge for paved lots, sectional for uneven surfaces Snow pusher guide →
- Buy before November — Canadian dealers sell out of popular sizes by mid-winter
Find a Snow Pusher Dealer →
Complete the job — you might also need:
✅ Last checked: March 2026
Source: skidsteerattachments.ca/catalog/snow-pushers/tmg-sp07-snow-pusher/
