John Deere TR72B 72 Inch Skid Steer Trencher🔵 Mid
🟢 Standard Flow
⚠ High-flow machine required
✓ Compatible with high-flow CTL
⚠ Too heavy for most small-frame machines
✓ Best on mid-frame or large-frame machines
View on brandt.ca →
Overview
The John Deere TR72B is a 72-inch depth chain trencher in the Worksite Pro attachment line for full-size skid steers. Used for deep utility and sewer installation by Canadian municipal contractors. Available through Brandt and John Deere dealers across Canada.
Canada Availability
Available in Canada through Brandt / John Deere Worksite Pro dealers.
Key Facts
- Model: John Deere TR72B
- Series: Worksite Pro
- Trench depth: 72 inches
- Type: chain trencher
- Drive: hydraulic chain drive
- Mount: John Deere quick attach (SSQA compatible)
- Weight: 700–2000 lbs
- Hydraulic flow: 15–30 GPM
✅ Specs sourced from brandt.ca · Last verified: March 2026
Is This Right For You?
✅ Buy if…
- You trench through soft to moderate soil for utilities, drainage, or irrigation lines at 36–60 inch depth
- Your soil is clay, loam, sandy loam, or river bottom — chain trenchers cut fast in these conditions
⛔ Skip if…
- Your soil is solid rock, dense caliche, or Shield granite — chain links and sprockets wear out fast in rock
- You trench in deeply frozen Prairie ground regularly — rock chain at 3–5× wear rate makes winter trenching expensive
🔍 Also consider…
- Rock wheel trencher if your ground is consistently rocky or hardpan
- Standard auger if you're drilling individual holes rather than continuous trench lines
🔧 Machine Compatibility
Designed for John Deere machines but mounts to any skid steer or CTL with a universal SSQA quick-attach plate.
About John Deere in Canada
John Deere attachments are available through an extensive Canadian dealer network, ensuring local service, parts availability, and warranty support coast to coast. Designed to pair with JD machines but compatible with any skid steer via universal quick attach.
Care & Maintenance
- Inspect chain teeth after every use — worn teeth slow penetration dramatically and increase drive motor load; a full day's work can dull a chain in abrasive soil
- Lubricate the drive chain and boom sprockets before each use and again after every 4 hours of continuous trenching
- Check the boom bar for cracking or deformation after work in rocky or abrasive conditions — boom cracks propagate quickly under the bending loads of trenching
- Clean soil from the drive motor cooling fins and chain case after summer use — compacted soil on the motor causes overheating on long cuts
- Store the chain with teeth protected from ground contact — resting a chain on carbide tips on concrete chips the teeth before you've even used it
How to Connect
- Attach trencher boom using Bob-Tach
- Connect high-flow hydraulic couplers
- Test chain tension and direction before cutting
- Call 811 and verify all utilities located before first cut
⚠ Safety NoteCanada-wide: call 811 before you dig. Hydraulic trenchers may need 20-35 GPM depending on rock hardness.
⛏️ Before You Buy a Trencher
Most chain trenchers require high-flow hydraulics — confirming your machine's output is the single most important step before purchase.
- Verify your machine outputs 18–30 GPM high-flow Check your flow spec →
- Chain trencher vs rock wheel — match to your soil and rock conditions Chain vs rock wheel →
- Call 811 before any dig — utility locate is required by law in Canada
Find a Trencher Dealer →
Complete the job — you might also need:
✅ Last checked: March 2026
Source: skidsteerattachments.ca/catalog/trenchers/john-deere-tr72b-trencher/
Ready to Buy? Check These First
⚙️
Confirm Machine Fit
Verify your machine's hydraulic flow meets this attachment's requirements before ordering. High-flow attachments need 25–45+ GPM — standard flow machines won't run them properly.
Check your machine's flow →
🇨🇦
Find a Canadian Dealer
Buy through a Canadian dealer for warranty support, parts, and service. Avoid grey-market imports on high-ticket attachments.
Find dealers by province →
