Case Skid Steer Stump Grinder Attachment🔵 Mid
🟡 High Flow
⚠ High-flow machine required
✓ Compatible with high-flow CTL
⚠ Too heavy for most small-frame machines
✓ Best on mid-frame or large-frame machines
View on casece.com →
Overview
Case Construction Equipment offers a stump grinder for their skid steer and CTL line. The hydraulic rotary cutter head grinds stumps to grade for landscaping and site prep work. Case has dealer coverage across Canada including tree services, landscapers, and general contractors doing lot clearing.
Canada Availability
Available through Case Construction Equipment dealers across Canada.
Key Facts
- Brand: Case Construction Equipment
- Type: hydraulic stump grinder
- Drive: hydraulic rotary cutter
- Mount: Case quick attach (SSQA compatible)
- Application: stump removal, landscaping, lot clearing
- Weight: 800–2500 lbs
- Hydraulic flow: 18–35 GPM
✅ Specs sourced from casece.com · Last verified: March 2026
Is This Right For You?
✅ Buy if…
- You remove tree stumps on residential or commercial properties where a dedicated stump grinder trailer isn't cost-effective
- Landscaping, tree service, or property clearing contracts where stump removal is part of the job
- You already run a skid steer and want to add stump grinding without a second piece of dedicated equipment
⛔ Skip if…
- Large hardwood stumps over 18 inches are your primary target — a heavy-duty grinder works more efficiently
- Stumps are tight against structures regularly — a side-shift model gives you access a standard unit can't
🔍 Also consider…
- Heavy-duty stump grinder for large-diameter hardwood stumps
- Side-shift stump grinder for tight obstacle-constrained work sites
🔧 Machine Compatibility
Designed for Case machines but mounts to any skid steer or CTL with a universal SSQA quick-attach plate.
About Case CE in Canada
Case Construction Equipment attachments are available through a national Canadian dealer network. Built to OEM standards and compatible with Case skid steers via universal quick attach.
Care & Maintenance
- Check carbide tooth torque before every use — loose teeth eject at high RPM and can cause catastrophic cutterhead damage or injury
- Replace carbide teeth in matching pairs (left-right balance) to maintain cutterhead balance and reduce destructive vibration
- Grease cutterhead drive spindle bearings after every 4 hours of operation — grinding generates significant heat and vibration that accelerates lubricant breakdown
- Clean wood chips and soil from the motor ventilation shroud and belt drive area after every use — blocked ventilation causes motor overheating
- Inspect hydraulic motor fittings for loosening after hard-material sessions — the constant vibration of grinding loosens threaded fittings progressively
How to Connect
- Attach stump grinder using Bob-Tach
- Connect high-flow hydraulic couplers
- Run wheel at idle to verify direction (wheel should spin into stump, not away)
- Clear 10m radius of bystanders before grinding
⚠ Safety NoteHigh-flow required (20-40 GPM). Always wear face shield and hearing protection.
🪵 Before You Buy a Stump Grinder
Virtually all skid steer stump grinders require high-flow hydraulics — and carbide tooth condition is a major operating cost factor.
- Confirm your machine delivers 15–35 GPM high-flow Check your flow spec →
- Match cutterhead width to your typical stump diameter range
- Factor in carbide tooth replacement cost — budget $300–800/season for regular use
Find a Stump Grinder Dealer →
Complete the job — you might also need:
✅ Last checked: March 2026
Source: skidsteerattachments.ca/catalog/stump-grinders/case-stump-grinder/
Ready to Buy? Check These First
⚙️
Confirm Machine Fit
Verify your machine's hydraulic flow meets this attachment's requirements before ordering. High-flow attachments need 25–45+ GPM — standard flow machines won't run them properly.
Check your machine's flow →
🇨🇦
Find a Canadian Dealer
Buy through a Canadian dealer for warranty support, parts, and service. Avoid grey-market imports on high-ticket attachments.
Find dealers by province →
