Erskine High Flow Skid Steer Brush Chipper🔵 Mid
🟡 High Flow
⚠ High-flow machine required
✓ Compatible with high-flow CTL
✓ Fits most skid steers, including small-frame
View on erskineattachments.com →
Overview
Erskine's high-flow brush chipper is designed for skid steers equipped with high-flow auxiliary hydraulics, pushing the chipping capacity to 8 inches — suitable for larger tree limbs and heavier clearing work. The larger 30-inch disc at 275 lbs provides the flywheel momentum needed to power through dense hardwood. Operates at 25-38 GPM at 3,000 PSI. The dual SSQA mount configuration allows parking the skid steer perpendicular or parallel to the chipper. Available through Canadian Erskine dealers.
Canada Availability
Erskine Attachments distributes through dealerships in Canada.
Key Facts
- Part number: 900791
- Chipper capacity: 8 inches
- Feed opening: 9" x 9"
- Feed system: independent hydraulic
- Chipper disc: 30" x 1.25"
- Disc weight: 275 lbs
- Operating weight: 1,525 lbs
- Hydraulic requirement: 25-38 GPM at 3,000 PSI (high flow)
- Case drain: required
- Mount: two universal SSQA plates
Is This Right For You?
✅ Buy if…
- You need to chip brush, limbs, and slash into transportable material rather than mulching in place
- Urban tree service, brush disposal contracts, or sites where leaving mulched material is unacceptable
- You want to produce usable wood chip material for landscaping or disposal
⛔ Skip if…
- In-place mulching is acceptable — a drum mulcher processes faster without relocating the machine
- You're clearing large acreage where chip transport logistics don't make sense
🔍 Also consider…
- Drum mulcher for in-place land clearing and brush processing
- Forestry mulcher for high-volume stand clearing where material stays on site
🔧 Machine Compatibility
Compatible with all skid steer brands and compact track loaders via universal SSQA quick attach. Mid-frame machines (S450–S650 class) are the most common fit.
About Erskine in Canada
Erskine is a US attachment brand with Canadian dealer coverage, known particularly for augers, soil conditioners, and specialty attachments. Erskine products are available at equipment dealers across Canada and are respected for quality build and reliable performance.
Care & Maintenance
- Inspect carbide hammers or teeth before every use — missing or broken hammers unbalance the rotor and can cause catastrophic motor damage at high RPM
- Replace worn teeth in matched sets across the rotor — even one missing hammer creates vibration destructive enough to damage drive motor bearings
- Grease rotor shaft bearing housings every 4–8 hours of operation, or more frequently in dusty or abrasive conditions
- Clean packed fibrous material from the housing interior and rotor after every session — buildup adds asymmetric weight and creates rotor imbalance
- Check the hydraulic motor case drain line monthly for leakage — a restricted or failed case drain causes motor shaft seal failure and internal leakage
How to Connect
- Attach mulcher head using Bob-Tach
- Connect high-flow hydraulic couplers
- Verify rotor direction — debris should eject downward, not toward operator
- Run at idle for 30 seconds before engaging rotor at working speed
⚠ Safety NoteMulchers are high-flow only (25-45 GPM+) — do not run on standard flow machines. Wear full PPE — flying debris risk.
🌲 Before You Buy a Mulcher
Mulchers are high-investment, high-flow attachments — the wrong match to your machine costs you in performance and potentially in repairs.
- Confirm your machine delivers 20–40 GPM high-flow Check your flow spec →
- Match drum vs disc mulcher to your material (trees vs brush) Drum vs disc guide →
- Verify carbide tooth compatibility for your primary soil/rock type
Find a Mulcher Dealer →
Complete the job — you might also need:
✅ Last checked: March 2026
Source: skidsteerattachments.ca/catalog/mulchers/erskine-brush-chipper-high-flow/
Ready to Buy? Check These First
⚙️
Confirm Machine Fit
Verify your machine's hydraulic flow meets this attachment's requirements before ordering. High-flow attachments need 25–45+ GPM — standard flow machines won't run them properly.
Check your machine's flow →
🇨🇦
Find a Canadian Dealer
Buy through a Canadian dealer for warranty support, parts, and service. Avoid grey-market imports on high-ticket attachments.
Find dealers by province →
